Metal wall art is a great way to add some personality and character to your home. Not only is it stylish, but it can also be quite practical. However, hanging heavy metal wall art can be a daunting task if you’re not sure how to do it properly. In this guide, we will walk you through the steps necessary to hang your metal artwork with ease. Let’s get started!
Table of Contents
Step 1: Choose a strong hanger
The first step is to choose a strong hanger that can support the weight of your artwork. If you’re not sure which hanger to use, ask a professional at your local hardware store. They will be able to recommend the best option for your particular piece.
Step 2: Find a stud in your wall using a stud finder
The next step is to find a stud in your wall. This will be the point where you will attach your hanger. To do this, you can use a stud finder which is available at most hardware stores.
Once you’ve found a stud, mark the location with a pencil so that you know where to drill your pilot hole later on.
Step 3: Mark where you wish to hang your art
Now that you’ve found a stud, it’s time to mark where you wish to hang your artwork. Using a level, hold the hanger up against the wall and mark the location of the holes. Once you’ve done this, set the hanger aside.
If you don’t have a level, no problem! You can improvise by using a book or any other straight edge.
Now that you’ve marked the locations of the holes, it’s time to drill your pilot holes. To do this, use a drill bit that is slightly smaller than your screws. This will ensure that your screws go in easily and without stripping the hole.
Once you’ve drilled your pilot holes, it’s time to insert your screws. Be sure to use screws that are long enough to go through the hanger and into the stud. Once your screws are in place, gently tighten them until they’re snug.
Step 4: Determine the hanger’s placement
There are a few things to consider when determining the placement of your hanger. The first is the weight of your artwork. If your piece is on the heavier side, you’ll want to place the hanger closer to the top so that it won’t pull down on the wall art and cause it to sag over time.
The second thing to consider is the size of your artwork. If you have a large piece, you may want to use two hangers so that it is evenly distributed and doesn’t put too much strain on one spot on the back of the metal wall art.
Once you’ve determined where to place your hangers, use a level to make sure they are even before you start drilling into the wall.
Step 5: Mark your exact hanging spot
Now that you’ve determined the placement of your hangers, it’s time to mark the exact spot on the wall where you will be drilling. We recommend using a pencil so that you can easily erase the marks later on.
Be sure to hold up your metal wall art in place before making any marks so that you know exactly where to drill.
Once you’ve marked the spot, set your artwork aside and get ready to drill!
If you don’t have a drill, no worries! You can always use a hammer and nail to create a hole for your screw. Just be sure to start with a smaller nail first so that you don’t damage your wall art.
Step 6: Secure the hanger on the stud
Now it’s time to secure your hanger to the stud. If you don’t have a stud finder, no worries! You can usually feel around for one by lightly tapping on the wall until you hear a solid sound.
Now that your first hanger is in place, repeat these steps for your second hanger (if using).
If you don’t have a stud finder, another option is to use wall anchors. Wall anchors are great for heavier pieces of metal wall art or for areas where it’s difficult to find a stud.
To use a wall anchor, simply drill your hole and then insert the anchor. Once the anchor is in place, screw your screw into the anchor. Be sure not to over-tighten the screw, as this could cause the anchor to become loose over time.
Step 7: Hang your metal artwork on the hanger
Now that your hangers are in place, it’s time to hang your metal artwork! We recommend using two people for this step, as it can be difficult to hold up a heavy piece of art while trying to screw it into place.
If you don’t have a second person to help, no worries! You can always use something like a chair or stool to prop up the artwork while you secure it to the hanger.
Once your artwork is in place, gently tighten the screws until they are snug. Be careful not to over-tighten the screws, as this could strip the threading and make them difficult to remove later on.
Step 8: Use a level to verify that your piece is even
Now that your artwork is hung, it’s important to verify that it is hanging evenly. This can be done by using a level or by measuring the distance from the top of the artwork to the bottom.
If you notice that your piece is not hanging evenly, you may need to make some slight adjustments to the placement of your hangers.
Once everything is even, congratulations! You’ve successfully hung your metal wall art!
Now that you know how to hang heavy metal wall art like a pro, it’s time to get started on your own gallery wall. Be sure to browse our selection of metal wall art for some inspiration. From modern abstract pieces to vintage-inspired designs, we’re sure you’ll find something that catches your eye. [1]
FAQ
How do you use a metal wall hanger?
To use a metal wall hanger, simply drill your hole and then insert the anchor. Once the anchor is in place, screw your screw into the anchor. Be sure not to over-tighten the screw, as this could cause the anchor to become loose over time.
How do you secure metal wall art?
There are a few different ways that you can secure metal wall art:
- Use hangers and screws
- Use wall anchors
- Use command strips
Which is best will depend on the weight and size of your particular piece of artwork. [2]
How do you hang a heavy piece of metal art?
There are a few things you’ll need before you get started: a drill, wall anchors, screws, and a level. You’ll also want to make sure the wall art is properly padded so it doesn’t scratch the surface it’s hung on.
To hang metal art on a wall, first, make pilot holes using a drill. After that, install the wall anchors and screws. Then, using the level to ensure it is straightened, hang the metal art on the screws. Finally, apply any pads or felt strips to the back of the metal art to protect it from damage.
How do you hang a metal frame on a wall?
The process is similar to hanging a heavy piece of metal art. Start by drilling pilot holes into the wall where you want to hang the frame. Then insert the wall anchors and screw them in place. Next, hang the frame on the screws and use the level to make sure it’s straight. Finally, add any pads or felt strips to the back of the frame to prevent scratching.
With a few simple tools and some basic instructions, you can easily hang metal wall art or frames in your home. Just be sure to take care when handling heavy pieces, and always use a level to ensure everything is hung correctly. With a little effort, you can transform any room in your home with beautiful metal wall art!
How do you hang a wire frame?
There are a few ways to hang wire frames, but the most common and effective method is to use nails. You’ll need two nails for each frame – one at the top and one at the bottom. Simply hammer the nails into the wall where you want to hang your artwork, and then place the wire over them. The wire should be taut, but not too tight – you don’t want it to sag in the middle. If it’s too loose, your artwork will wobble; if it’s too tight, it could break.
Another way to hang wire frames is by using picture hangers. These are small metal hooks that come with adhesive pads. Just peel off the backing on the adhesive pad and stick it to the back of your frame, then hang it on the nail. Picture hangers are great if you’re worried about damaging your walls – they won’t leave any holes or marks.
If you’re hanging a particularly heavy piece of artwork, you may want to use screws instead of nails. Just screw the screws into the wall (using a drill if necessary), and then place the wire over them. This method is more secure, but it will damage your walls more if you ever need to remove it.
How do you hang a large picture with a wire?
The first step is to use a stud finder to locate the wall studs. Once you know where the studs are, mark their location with a pencil on the wall. Next, measure the distance between the two marks and divide that number by three. This will be the center of your picture.
Now it’s time to measure the wire. Cut a piece of twine or fishing line that is about two inches longer than the width of your frame. Tie each end of the wire to an eye hook, and then thread the other end through the metal loops on either side of your frame. Center your frame over the pencil mark on your wall and make sure that it is level before attaching it to the wall with screws.
Now all you have to do is hang your artwork on the wire! Make sure that the hooks are securely in place before letting go of your artwork. If everything looks good, step back and admire your handiwork! [3]
How do you hang a heavy picture with two hooks?
There are a few different ways that you can hang a heavy picture with two hooks. The first way is to use two nails, one in each top corner of the frame. Hammer the nails into the wall at an angle so that they create a stable base for the frame to hang from. Then, simply place the frame onto the nails.
Another way to hang a heavy picture with two hooks is to use Command strips. These are large adhesive strips that come with their own removable hooks. To use them, simply remove the backing from the strip and press it firmly against the wall where you want to hang your frame. Then, place your frame onto the hook and press it firmly against the strip to secure it in place.
If you’re hanging a particularly heavy frame, you may want to use both nails and Command strips together for extra support. Whichever method you choose, be sure to test that your frame is secure before letting go completely. [4]
How much weight can a picture wire hold?
Picture wire is designed to hold a variety of weights, depending on the gauge or thickness of the wire. For example, an 18-gauge wire can typically hold up to 20 pounds, while a 14-gauge wire can hold up to 50 pounds. When in doubt, it’s always best to err on the side of caution and go with a thicker wire that can support more weight. That way, you can be sure your heavy metal wall art will stay put.
Now that you know how to hang heavy metal wall art, it’s time to get creative and start decorating your home! Be sure to follow the tips above to ensure that your artwork is securely hung and enjoy your new décor. [5]
How do you weatherproof metal art?
Metal art can be weatherproofed in several ways. One way is to apply a clear sealant or lacquer to the metal. This will create a barrier between the metal and the elements, helping to prevent rust and corrosion. Another way to weatherproof metal art is to apply a patina. This is a thin, protective coating that helps to prevent oxidation. Patinas can be applied with a brush, spray, or even by dipping the metal piece into a patina solution. You can also purchase pre-weathered metal art that has already been treated with a patina solution. Whichever method you choose, be sure to follow the instructions carefully and allow ample time for the waterproofing solution to dry completely before exposing your metal art to the elements.
What grit sandpaper should I use before a clear coat?
The type of grit sandpaper you should use depends on the condition of the metal surface. If the surface is rough or has a lot of imperfections, you’ll want to start with a coarse grit sandpaper (60-80 grit). For surfaces that are in good condition, you can start with a medium grit sandpaper (100-120 grit). Once the surface is smooth, you can finish with a fine grit sandpaper (200-400 grit) before applying a clear coat. Following these steps will help ensure that your metal art has a smooth, professional finish.
Useful Video: How to install Metal Wall Art by Inspire Metals
Conclusion
Now that you know how to hang heavy metal wall art like a pro, go forth and add some personality to your walls! With a few simple steps, you can create an eye-catching display that will be the envy of your friends and neighbors. Have fun with it – mix and match different sizes, shapes, and styles to create a look that is uniquely yours. And remember, if at any time you have questions or need help, our team is always here to assist. Thanks for reading, and happy decorating!
References:
- https://www.shutterfly.com/ideas/how-to-hang-metal-wall-art/
- https://kanyanaengineering.com.au/how-to-hang-metal-wall-art/
- https://www.thespruce.com/how-to-hang-a-picture-with-wire-5195068
- https://www.theorganizedmama.com/how-to-hang-a-picture-with-two-hooks/
- https://www.ashanging.com/en_ca/blog/post/how-hang-heavy-picture